Data Aging - Image Level iDataAgent
- This product is deprecated for AIX and Linux. New installations of the Image Level Agent are no longer supported in V10, but the agent will continue to function normally. Upgrade to the latest service pack in V10 is supported. You cannot use your installed version of the Image Level Agent to perform backups in the next version of SnapProtect.
- This functionality is now available using Block-Level Backup. We recommend that you begin backing up data by using the block-level backup method instead of using the Image Level Agent as soon as you are able to. No new license is required for Block-Level Backup. For instructions on transitioning to block-level backups, see Transitioning from Image Level Agent to Block-Level Backups.
See Deprecated Features, Products, and Platforms for comprehensive information on deprecated products.
Data Aging is the process of removing old data from secondary storage to allow the associated media to be reused for future backups.
By default, all backup data is retained infinitely. However, you should change the retention of your data based on your needs. Note that if you continue to have infinite retention, you will also need infinite storage capacity.
Setting Up the Basic Retention Rule
- From the CommCell Browser, expand Policies | Storage Policies | <Storage Policy>.
- Right-click the appropriate storage policy copy, and then click the Properties.
- In the Copy Properties dialog box, click the Retention tab.
- Under Basic Retention Rule for All Backups, click the Retain For.
- Enter number of days to retain the data.
- Enter number of cycles to retain the data.
- Click OK.
- In the Confirm Basic Retention dialog box, click Yes.
On the ribbon in the CommCell Console, click the Reports tab, and then click Forecast.Under Reports pane, Data Retention Forecast and Compliance is selected by default.
- Click Run.
- The report will display the data to be pruned when a data aging job is run.
To ensure only data intended for aging is actually aged, it is important to identify the data that will be aged based on the retention rules you have configured. Hence, ensure this report includes only the data you intend to age.
If necessary, fine-tune your rules so that only the intended data is aged.
Once you run a data aging job, the data will be pruned.
Running the Data Aging Job
- From the CommCell Console, right click the CommServe node, point to All Tasks and then click Data Aging.
In the Data Aging Options dialog box, click OK.
- You can track the progress of the job from the Job Controller window. When the job is completed, in the Job Controller the Status will be displayed as Completed.
Make sure that the job completes successfully. If the job did not complete successfully, rerun the job.
Extended retention rules can be used in the following circumstances:
- If you have a single drive tape library
- If you want to create a hierarchical retention scheme (grandfather-father-son tape rotation)
Extended retention rules allow you to define three additional "extended" retention periods for full (or synthetic full) backups. For example:
- You may want to retain your weekly full backups for 30 days.
- You may want to retain your monthly full backup for 90 days.
- You may want to retain your yearly full backup for 365 days.
A backup job will be selected for extended retention based on its start time. For example: If a backup job starts at 11:55 pm on August 31st and ends at 1 am on September 1st, then it will be selected as the last full backup for the month of August and will be picked up for extended retention.
In all other cases, we recommend you to use Auxiliary Copy for extended storage as it actually creates another physical copy of the data, thereby reducing the risk of data loss due to media failure.
Setting Up the Extended Retention RulesUse the following steps for setting up the extended retention rules:
- Right-click the storage policy copy and click Properties.
- Click the Retention tab.
- Set the basic retention rules by clicking Retain for and entering the number of days and cycles appropriate for your organization.
- Set the extended retention rules as follows:
- Click the For button.
- Enter the number of Days Total to retain the backup.
- Click the Keep drop-down list, and select the desired backup criteria (e.g., Monthly Full, Weekly Full).
- Click the Grace Days drop-down list and select the number of days (e.g., 2).
This allows you to consider the additional number of days along with the Extended Retention rule. For example, if the last full backup job fails with in the defined extended retention criteria, then the next full backup job that ran in the specified grace days will be selected for retention.
- Repeat Step 4 to configure additional extended retention.
- Click OK.
Provides comprehensive information on additional capabilities for the following features: