Deploying a File Recovery Enabler for Linux
A File Recovery Enabler for Linux enables virtual machine data to be browsed from a backup for the source virtual machine (VM), with support for ext2, ext3, ext4, XFS, JFS, HFS, HFS Plus, and Btrfs file systems. Use the open virtual appliance (OVA) template supplied by SnapProtect to create a virtual machine that contains the File Recovery Enabler.
- Before creating a virtual machine for Linux file restores, install the latest available service pack for SnapProtect on the CommServe host and Virtual Server Agent.
- Use the latest available version of the File Recovery Enabler template. The template version must match the service pack version.
- To verify the version of VMware software that is required to support this feature, see System Requirements.
- Requirements for the ESX server where the File Recovery Enabler is deployed:
- Deployment uses 4 GB of RAM
- Deployment uses 4 vCPUs
- Disk requirements: 80 GB (thin or thick provisioned)
- Verify that network communication is enabled so that the VMware servers, the CommServe system, and the machine where the File Recovery Enabler is deployed can communicate with each other.
- If a firewall is used, see Entering Required Firewall Settings.
- The virtualization client must refer to a vCenter user with permissions defined as described in User Accounts.
- The following vSphere permissions are required to enable deployment or reconfiguration of a File Recovery Enabler for Linux:
Category Available Permissions vApp Import vApp vApp application configuration vApp vApp instance configuration
- The following SnapProtect permissions must be assigned for the CommServe user account in the CommCell Console:
Category Permission Usage Global Administrative Management Enables the CommServe user (identified as CS User Name below) to deploy the File Recovery Enabler in the CommServe system. Client Agent Management Enables the File Recovery Enabler to be added to a client computer group.
- The File Recovery Enabler can be deployed on the same vCenter and ESX server that is used for VMware backup, or on any other vCenter or ESX server with which the File Recovery Enabler can establish a connection.
- Live recovery is only supported for recovery from backups using magnetic disk libraries, not from backups to tape libraries.
- The File Recovery Enabler does not support Live Browse and file recovery operations for subvolumes of logical volumes in XFS or Btrfs.
- The File Recovery Enabler for Linux supports NFS version 3.
- After deploying the File Recovery Enabler, download and install HotFixes for the installed service pack.
- Log in to the NetApp Support web site and navigate to SnapProtect > Core and Service Packs. Go to the Linux MediaAgent OVA template section and download that package to a location that is accessible from the vCenter. Ensure that the service pack for the package matches the installed service pack.
- In vCenter, click the File menu and select Deploy OVF Template.
- Browse to the location where the File Recovery Enabler for Linux template file is located and select that file; then click Next.
- Review the OVF Template Details dialog and click Next.
- On the Name and Location dialog, enter a name for the virtual machine (for example, VM_LinuxFileRecoveryEnabler); then click Next.
- On the Host / Cluster dialog, select a data center and ESX server; then click Next.
- On the Resource Pool dialog (optional), select a resource pool and click Next.
- On the Storage dialog, select a datastore and click Next.
- On the Disk Format dialog, click Next to accept the default format.
- On the Network Mapping dialog, select the source and destination networks as needed; then click Next.
- On the Properties dialog, enter the following information:
- CS Configuration:
- CS Client Name - Short name for the CommServe system. This entry is case sensitive.
- CS Hostname - Host name or IP address for the CommServe system. This entry is case sensitive.
- CS User Name - User name for the CommCell Console.
- CS Password - Password for the CommCell Console user.
- Client Configuration:
- Client Name - Short name for the virtual machine (for example, VM_LinuxFileRecoveryEnabler).
- Client Hostname – Host name or IP address for the client.
- New root password - Password for the root user of the virtual machine.
- Client Group Name – Name of a client computer group; the File Recovery Enabler is assigned to that group if the group exists (the name is case sensitive).
- IP Configuration:
Note: The following fields need to be entered when the File Recovery Enabler is being deployed using a static IP address, or with DHCP if there is a possibility that the DHCP server in your environment provides incorrect or incomplete DNS information. The fields below override any DNS configuration that is obtained from the DHCP servers.
- Use DHCP - Select this option or enter values for the Static IP Address, Netmask, and Gateway.
- DNS Search Suffix - Identifiers for domains to be supported. You can enter multiple search suffixes separated by whitespaces.
- Name Server 1 - IP address for the primary name server.
- Name Server 2 - IP address for the secondary name server.
- Firewall Configuration - Indicate whether the CommServe system is behind a firewall and enter values for Option 1, Option 2, or Option 3:
- Is CS behind a firewall? - Select this option if a firewall is enabled on the CommServe system.
- [Option 1] CS f/w tunnel port (client can connect to CS) - Enter the tunnel port number the client can use to open a connection to the CommServe system.
- [Option 2] Client f/w tunnel port (CS can connect to client) - Enter the tunnel port number the CommServe system can use to open a connection toward the client.
- For Option 3, enter all of the following values:
- [Option 3] Proxy Hostname (CS reachable via proxy)
- [Option 3] Proxy Clientname (CS reachable via proxy)
- [Option 3] Proxy port number (CS reachable via proxy)
- If an HTTP proxy is used for communication between the CommServe host and the File Recovery Enabler, provide the following information:
- HTTP Proxy Hostname
- HTTP Proxy Port
- CS Configuration:
- After verifying the information, click Next.
- On the Ready to Complete dialog, review the deployment options and click Finish.
- Configure a default File Recovery Enabler for Linux to use for UNIX-based file restores as described in Specifying the Default File Recovery Enabler for Linux for a Virtual Server Instance, and an ESX server to host the NFS datastore as described in Identifying a Proxy ESX Server for the File Recovery Enabler.
Note: If you still experience connection issues after deployment, you can also add fully qualified host names and IP addresses for the File Recovery Enabler and the CommServe system to the /etc/hosts files for both machines to ensure that both systems can resolve host names locally.
As needed, the OVA template for the File Recovery Enabler is updated to include operating system updates and enhancements. To ensure that the File Recovery Enabler contains all critical fixes and features, upgrade the CommServe host and Virtual Server Agent to the latest service pack, and download the latest OVA template for the File Recovery Enabler to deploy the File Recovery Enabler.
If you have deployed an older version of the File Recovery Enabler, decommission the older version and deploy a new one as described in Procedure.
What To Do Next
Perform the following additional tasks:
- Verify the registration for the File Recovery Enabler VM.
- Review Cache Requirements to ensure that there is sufficient space for file recovery data.
- If a firewall is used, enter Required Firewall Settings.
- Optional: Instead of deploying the File Recovery Enabler as a virtual machine, you can convert a Linux MediaAgent to a File Recovery Enabler for Linux.